Search found 263 matches

by jhalfhide
Sat Aug 18, 2018 1:09 pm
Forum: Technical discussions
Topic: 2010 SMT has been in shop for six weeks!
Replies: 11
Views: 358

Re: 2010 SMT has been in shop for six weeks!

SuaveDave wrote:Coil swap performed. Coil’s good, error code not. Perhaps something to do with the dongles installed during the SASectomy?
Simply turn off the SAS using TuneECU and do away with the dongles. The SAS shouldn’t case this issue though.


Sent from my iPhone using Tapatalk
by jhalfhide
Fri Aug 17, 2018 9:34 pm
Forum: Technical discussions
Topic: 2010 SMT has been in shop for six weeks!
Replies: 11
Views: 358

Re: 2010 SMT has been in shop for six weeks!

Simple thing I’m not seeing is a coil pack swap between #1 & #2. If it fails again with an error and it’s followed the same coil, just replace it. You don’t know that the repair they did on the coil is good.


Sent from my iPhone using Tapatalk
by jhalfhide
Sat Jul 28, 2018 12:24 pm
Forum: Technical discussions
Topic: Front Sprocket nut righty tighty lefty loosey?
Replies: 5
Views: 394

Re: Front Sprocket nut righty tighty lefty loosey?

100nm is the manual’s recommendation. I didn’t have an extension for my torque wrench so couldn’t get in there. Ended up gunning it back on [emoji23]


Sent from my iPhone using Tapatalk
by jhalfhide
Fri Jul 27, 2018 5:27 pm
Forum: Technical discussions
Topic: Front Sprocket nut righty tighty lefty loosey?
Replies: 5
Views: 394

Re: Front Sprocket nut righty tighty lefty loosey?

It’s the usual lefty loosey. Mine took a 450nm electric impact gun and still didn’t budge for a while [emoji51]


Sent from my iPhone using Tapatalk
by jhalfhide
Thu Jul 19, 2018 12:01 am
Forum: Accessories
Topic: LIGHT Bulb for Auxilliary lights on SMT
Replies: 3
Views: 449

Re: LIGHT Bulb for Auxilliary lights on SMT

No idea unfortunately, they were on the bike when I purchased it.


Sent from my iPhone using Tapatalk
by jhalfhide
Fri Jul 13, 2018 7:18 am
Forum: Accessories
Topic: LIGHT Bulb for Auxilliary lights on SMT
Replies: 3
Views: 449

Re: LIGHT Bulb for Auxilliary lights on SMT

They’re LED and I believe, sealed units with no bulb replacement. You could just get a cheaper set, like my safego ones, and wire them up to the same wires for the same operation.

Image


Sent from my iPhone using Tapatalk
by jhalfhide
Wed Jul 11, 2018 7:50 am
Forum: Teething problems
Topic: GRRRRR Shop screwed up my fuel level sensor
Replies: 2
Views: 271

GRRRRR Shop screwed up my fuel level sensor

Back to dealer.
by jhalfhide
Sun Jul 08, 2018 4:45 pm
Forum: Technical discussions
Topic: Which oil to use?
Replies: 5
Views: 429

Which oil to use?

Castrol Power One Racing 10w50. Been using it yonks and bike likes it more than OEM


Sent from my iPhone using Tapatalk
by jhalfhide
Sat Jul 07, 2018 4:39 pm
Forum: Technical discussions
Topic: HELP my bike is beeping
Replies: 6
Views: 465

Re: HELP my bike is beeping

So what openings did the map have before. Maybe your flies were barely open, creating the whistling (big air, tiny gap). If opening the flies has cured it, I’d either leave them as they are or go back to the old map but increase the openings at that rpm range by 10% Sent from my iPhone using Tapatalk
by jhalfhide
Fri Jul 06, 2018 7:26 pm
Forum: Technical discussions
Topic: HELP my bike is beeping
Replies: 6
Views: 465

Re: HELP my bike is beeping

You’re right, that’d drive me mental. Sounds like a Girl Scouts whistle rather than a snarling beast.

I think you’ve got an air leak somewhere. Double check your air box fitment, check the rubbers around the throttle bodies too.


Sent from my iPhone using Tapatalk
by jhalfhide
Sun Jul 01, 2018 10:15 am
Forum: Technical discussions
Topic: Cheap air box that works
Replies: 335
Views: 97305

Re: Cheap air box that works

A foam filter will always break down eventually, but I’ve got 9000 miles on mine and no signs of it yet. Are you keeping it oiled enough? They’re not exactly expensive either so if I have to replace every 4-5 years, it’s not an issue. Cleaned mine last service and it came out fine. Sent from my iPho...
by jhalfhide
Sun Jul 01, 2018 7:58 am
Forum: Teething problems
Topic: Rear brake lever is contacting clutch case
Replies: 10
Views: 1851

Re: Rear brake lever is contacting clutch case

It was indeed the bearings in the brake pedal. I purchased them from a KTM dealer. They come individually so order 2. Getting them in/out is fun [emoji19]


Sent from my iPhone using Tapatalk
by jhalfhide
Sat Jun 30, 2018 7:14 am
Forum: Exhausts
Topic: Akrapovic Noise Reduction Insert
Replies: 5
Views: 1520

Re: Akrapovic Noise Reduction Insert

No problem, glad you got it sorted.


Sent from my iPhone using Tapatalk
by jhalfhide
Fri Jun 29, 2018 7:57 am
Forum: Exhausts
Topic: Akrapovic Noise Reduction Insert
Replies: 5
Views: 1520

Re: Akrapovic Noise Reduction Insert

They do different angles so check your pipes with a protractor


Sent from my iPhone using Tapatalk
by jhalfhide
Thu Jun 28, 2018 7:11 pm
Forum: Exhausts
Topic: Akrapovic Noise Reduction Insert
Replies: 5
Views: 1520

Re: Akrapovic Noise Reduction Insert

PipeWerx make some aftermarket ones. They’re listed on eBay UK. Not sure about your side.
https://rover.ebay.com/rover/0/0/0?mpr ... 1225215577


Sent from my iPhone using Tapatalk
by jhalfhide
Tue Jun 26, 2018 10:50 am
Forum: Exhausts
Topic: Do you know DOMINATOR exhaust
Replies: 22
Views: 5604

Re: Do you know DOMINATOR exhaust

The sensor is in the headers so these exhausts would work


Sent from my iPhone using Tapatalk
by jhalfhide
Mon Jun 25, 2018 6:54 pm
Forum: Technical discussions
Topic: Bike creeping when clutch pulled in?
Replies: 2
Views: 274

Re: Bike creeping when clutch pulled in?

Sounds like a blocked oil jet or it needs an oil change. Mine usually does this when it’s in need of an oil change. Oil change usually sorts it right out and neutral is easy to find again. I use 10w50 Castro Power One Racing. If it’s a blocked oil jet, that’s easy to do and many guides online. Sent ...
by jhalfhide
Sat Jun 23, 2018 7:21 am
Forum: Technical discussions
Topic: Water pump impeller - destructive removal (60035055100)
Replies: 2
Views: 230

Re: Water pump impeller - destructive removal (60035055100)

That’s the good thing about these bikes, the fixes are all really cheap. Just placed an order for £10 last night, just for a few O-Rings and screws that I’m replacing.


Sent from my iPhone using Tapatalk
by jhalfhide
Sun Jun 17, 2018 9:36 am
Forum: Technical Discussions
Topic: Exhaust Servo
Replies: 29
Views: 6990

Re: Exhaust Servo

Same as the Ducati exhaust valves. Only there for noise restriction for the testing. Does nothing for tuning power or exhaust flows.


Sent from my iPhone using Tapatalk
by jhalfhide
Mon Jun 11, 2018 7:30 am
Forum: Technical discussions
Topic: 990 SMT to 990 Adventure
Replies: 1
Views: 274

Re: 990 SMT to 990 Adventure

My thoughts are, buy the adventure and get the bigger tanks too.


Sent from my iPhone using Tapatalk